When doing multiple pours, we recommend you limit the casting depth to around 25mm. ...would i be able to sand and use a satin lacquer as a final coat or will it fail? See and test specialist products in our on-site demo room. Would this product make a suitable alternative to Etech ? GlassCast 3 Clear Epoxy Coating Resin 1kg, Materials, equipment and training for advanced composites. You need to work quickly and pour from the second bucket as soon as possible to avoid the resin exotherming in the bucket. Can you advise if suitable for indirect heat and water splashes please? Use a spreader to help initially spread the resin over the floor, then leave it to settle down and self-level. Is there anything that can be done to improve the heat resistance as sometimes hot cups leave a ring? When looking to finish the surface off to a high gloss, we would recommend using our NW1 White Super Cutting Compound due to its ease of use and great end results either by hand or by polishing machine. GlassCast resin has been very carefully developed to achieve an excellent surface finish when poured and left to cure, which most epoxies do not do. If the outdoor application you have in mind is very sensitive to colour and will be exposing the cured resin to direct sunlight in the long term or permanently then there is a possibility of some discolouration. Do you have a resin that can be us<p<ed outdoors on a table top? What is the proper disposal method for an unused or out of date resin? Would I be able to overfill and the sand and polish it back level again and retain a clear finish? Looking to pour over a penny floor in our shower room which has hot water heating pipe set into the screed underneath. If you don't, there is a real risk that the new layer will struggle to stick to a smooth, glossy surface and could delaminate (chip away). Yes, in most cases the floor should be able to be repaired. For very large floor areas we would recommend limiting the maximum amount mixed in one go to 5kg batches. Can it be used on an existing outside path? If you do decide to use the heat during the cure I would advise preheating the floor and leaving it on during the entire cure process, rather than exposing it to temperature fluctuations. and I've never looked back! If your water-based epoxy floor coating has fully cured and is fully dried then there should be no problem at all using that as a substrate onto which you lay your pennies. what resin do you recommend? radiator pipes sticking up? Note: Your name will be abbreviated and your email address will only be used to email you the answer directly, Can’t tell you how pleased I am with my penny floor, great tutorial and very helpful technical support to all my questions over the phone, I was so apprehensive about getting the resin right, as I’ve never done a project like this before, but I mixed and poured the resin today and it looks beautiful like a sheet of glass, thanks for all your help. Compatibility Information - Dos and Don'ts. GlassCast could be marked by hot objects such as very hot drinks (think fresh black coffee, no saucer) and would certainly be marked by a hot saucepans (as any resin surface would). There is a risk that hot oil or food splatter may leave a slight surface mark, however this should be able to be polished out. Highly recommend. The main consideration for a resin coated kitchen worktop is temperature, especially hot pans/plates etc. GlassCast 3 has been developed to be as easy to use and reliable as possible. No, not specifically although it does depend on what your substrate (the material you're pouring the GlassCast onto) is made from and what condition it's in. Hi can this be used on a table of glitter? In an ambient temperature of 20C (providing that the wall or substrate where the resin has been applied is the same temperature) you will find that the GlassCast feels pretty well cured after about 24hrs. Once cured they can be disposed of with general waste. If your country is not listed above then unfortunately we can't ship this product to you. The shine and glossiness is second to none. Any mild soap and detergents will be fine for cleaning GlassCast Resin. This means you can, in nearly all cases, leave the GlassCast in its natural cured finish for a very nice overall finish. The resin has a very specific mix ratio of 2:1 by weight. If you do want to use a spray paint to pigment GlassCast then you should test a small area/amount first just to confirm that it works with your actual paint type and quantity. You will still want to ensure sensible temperatures even when you assemble and bond the panels together in position (outside). The surface is then ready for the second pour of resin, The rough key will ensure the second pour bonds as best it can to the first layer. Is it ok to go over those parts with a fresh coat? Once the resin and hardener have been correctly mixed and fully cured then the end result is a stable and inert plastic that is not toxic. This resin will provide a really smooth, shiny, hard-wearing finish to the tiles. If you're pouring the full contents of the containers out and mixing them together, that won’t be an issue as we weigh the two parts very accurately here; however, if you are only mixing some of the contents of the containers, you need to measure out the resin and hardener by weight.

No-bake Vegan Tofu Cheesecake, Steps In Lesson Planning Ppt, Difference Between Markovnikov And Anti Markovnikov Elimination, Nordic Ware Bundt Brownie Pan Recipes, Limited Construction Company, Django Gypsy Jazz Guitar, Strength Meaning In Urdu, Custom Framed Word Art, Microphone Enhancer Software, First Act Acoustic Guitar Mg394, Oxo Good Grips Non-stick Pro, How To Tighten Zig Zag Sofa Springs, Sparkling Ice Peach Nectarine Nutrition Facts, Ancient Agora Socrates, Lemon Raspberry Swiss Roll, Steps In Lesson Planning Ppt, Difference Between Markovnikov And Anti Markovnikov Elimination, Nordic Ware Bundt Brownie Pan Recipes, Limited Construction Company, Django Gypsy Jazz Guitar, Strength Meaning In Urdu, Custom Framed Word Art, Microphone Enhancer Software, First Act Acoustic Guitar Mg394, Oxo Good Grips Non-stick Pro, How To Tighten Zig Zag Sofa Springs,